Quick answer: Here is how to replace spikes on cricket shoes that use screw in spikes: brush the sole clean, loosen each old spike counterclockwise with a spike spanner, clear dirt out of the socket, then thread the new spike in by hand and tighten it with the spanner until snug. Molded rubber cleats, like those on most club cricket shoes, cannot be swapped out.
Worn spikes are easy to miss until you slip at the crease. The tips wear down a little every match, and one loose spike can work its way out on a run up without you noticing. Learning how to replace spikes on cricket shoes takes a spanner and a little patience, and it keeps a pair you are happy with in use for longer. This guide covers which shoes have replaceable spikes, when to change them, the six steps, and what to do when a spike will not budge.
Which cricket shoes have replaceable spikes
Look at the sole before you buy anything.

| Sole type | What it looks like | Can you replace the spikes? |
|---|---|---|
| Screw in spikes | Threaded spikes, often metal, each sitting in its own socket | Yes |
| Molded rubber cleats | Cleats formed as one piece with the sole | No |
| Turf sole | Flat rubber sole with small studs | No |
Screw in spikes are mainly found on full spike shoes worn by fast bowlers on grass. Most club cricket shoes in the US use molded rubber cleats, which grip well on hard ground but wear with the sole. Our guide to cricket shoes with rubber spikes explains that type in more detail, and our guide to cricket bowling shoes covers why fast bowlers choose screw in spikes.
When to replace spikes on cricket shoes
Check your spikes every few weeks during the season and before the first match of the year. Replace them when you see any of these:
- The tips are worn flat or rounded
- You slip at the crease or on the turn when you used not to
- A spike is missing, bent or loose in its socket
- Rust has formed on a steel spike
Change the whole set at once rather than one or two spikes. New and worn spikes side by side give uneven grip.
What you need
- A cricket spike spanner, sometimes called a spike key
- A new set of spikes with the same thread as your shoes
- A stiff brush and a cloth
- A toothpick or small pick for cleaning the sockets
Most spike sets come with a spanner. Check the thread size before you buy: a spike with the wrong thread will not seat properly and can damage the socket.
How to replace spikes on cricket shoes in six steps

- Clean the sole. Brush off dried mud and grass so the spanner can sit flat on each spike.
- Fit the spanner. Line up its prongs with the holes or slots on the spike and press it down firmly.
- Turn counterclockwise. Loosen the old spike and unscrew it by hand once it moves. Work on one spike at a time.
- Clean the socket. Pick out any dirt from the thread with a toothpick, then wipe it dry.
- Thread the new spike by hand, clockwise. It should turn easily for the first few turns. If it resists, back it out and start again, because forcing it can cross the thread.
- Tighten with the spanner until snug. Firm is enough. Overtightening can strip the socket.
Repeat for each spike, then check them all again after your first session in the new set.
How to loosen a stuck spike
A spike that will not move is usually held by packed dirt or rust, not by the thread itself.
- Brush and pick out as much dirt as you can from around the base.
- Wet the area with a little warm water and leave it for a few minutes to soften dried mud.
- Press the spanner down hard so it does not slip, then turn with slow, steady pressure rather than sudden force.
- Avoid pliers on the spike head. They round it off and make the spike harder to remove.
If a socket is damaged, stop and contact the shoe maker. For SOLM8 footwear, the warranty page sets out what the warranty does and does not cover.
Looking after spikes between matches
- Dry your shoes at room temperature after wet matches. Steel spikes rust faster if they are stored damp.
- Brush the sole after each match so dirt does not set hard around the spikes.
- Keep the spanner and a few spare spikes in your kit bag.
SOLM8 S60 Pro and spare spike sets
The S60 Pro is the SOLM8 shoe with screw in metal spikes, set among rubber studs. The S4, S8 3.0 and S70 are rubber cleat models and cannot take metal spikes.
SOLM8 sells spare spike sets in the cricket shoe accessories collection. The product pages list 24 spikes per set, a spanner in the box and a 1/4 inch thread. Check that thread against your shoes before you buy.

FAQ
Can you replace spikes on any cricket shoe?
No. Only shoes with screw in spikes have replaceable spikes. Shoes with molded rubber cleats or turf soles have the studs formed into the sole, so they cannot be swapped.
How often should you replace cricket spikes?
Check them every few weeks in the season and before your first match of the year. Replace the full set when the tips are worn flat, a spike is missing or loose, or you start slipping at the crease.
Which way do you turn to remove cricket spikes?
Turn counterclockwise to loosen and remove a spike, and clockwise to fit a new one. Start the new spike by hand, then tighten it with the spanner until snug.
What do you need to replace cricket spikes?
You need a spike spanner, a new set of spikes with the same thread as your shoes, a stiff brush and something small to clean out the sockets. Most spike sets include a spanner.
SOLM8 Cricket Shoes
Find your next pair
Find your next pair in the 2026 cricket shoes collection, with free standard shipping on US orders over $40. Joining the SOLM8 email list gets you 10% off your first order.
About the author
SOLM8 Team
SOLM8 is a US based cricket footwear brand co founded by Bhupinder Singh Kharbanda (BSK), who has designed cricket shoes for more than 25 years. The SOLM8 Team writes practical guides for cricket players and fans in the US, drawing on that design experience and on what club players tell us about their shoes.
